Vertical Hit And Miss Fence Panels

Vertical Hit and Miss Fence Panels

About the panel 

Vertical Hit and Miss panels are so called due to the pales being affixed to alternative sides of the panel creating a hit and miss design. In its vertical orientation the pales are fixed vertically onto the panel.

Part of our good both sides range, both sides of the panel have the same design, so you and your neighbour have the best-looking side of the fence. Built using planed boards so the finish is smooth and gives a high-quality feel. An advantage of the Hit and Miss style is that the slatted panel design has an approx. 15% wind load reduction as the gaps between the pales allows air to pass through.

Vertical Hit and Miss panel boards run vertically rather than our alternative Horizontal Hit & Miss.

Panel Specification

Our Vertical Hit and Miss fence panels are made using our trademark vacuum pressure treated Jakcure® softwood timber, guaranteed for 25 years. Built using stainless steel fixings to ensure longevity, our fence panels are built to last.

• Panels are 1.83m wide
• Panels are 51mm thick
• Framing is 45mm x 51mm recessed to take boards
• Vertical boards are 95 x 8mm with internal battens 50 x 12mm

Please Note: dimensions may increase by 6% when first delivered as our treatment process can temporarily cause the product to swell.

Fence Post Options – Standard Slotted Jakpost®, Heavy Duty Slotted Jakposts® , Mi-T® Metal Garden Fence Post​

​Gravel board options-  Standard Gravel Board , Hedgehog Friendly Gravel Board 

To meet the conditions of the 25 year guarantee, gravel boards are required where panels are in contact with the ground.

​Installation Advice Installation Instructions 

Reducing the width of the fence panel –  All fence panel are 1.83m wide as standard, if you require a narrower fence panel, you can cut the fence panel down on site using our cut down kit. Please remember to treat any cut ends with Jakcure Cut Treatment, to ensure you adhere to our 25-year guarantee guidelines.

Recommended Fixings

We recommend using 6 screws per panel or 12 per panel if using capping rails plus an additional 4 per gravel board. 60mm, stainless steel, self-drilling countersunk screws are available in packs of 100 or 200 to secure panels to posts. Panels should be screwed to the posts to secure the fence run.

If you require a non standard width panel e.g. to complete your fence run you would need 5 ½ panels, add a cut down kit to your basket in order to be able to cut the panel to the required size. Alternatively, please give us a call to speak to us about ordering a bespoke panel.

We recommend using our slotted Jakposts for intermediates, ends and corners, click on the button below to see the range

Slotted Posts

Gravel boards need to be used when panels are in contact with the ground as part of the 25 year Jakcure® guarantee. More details can be found on our Jakcure T&Cs page.

Gravel Boards

Capping Rails can be used on these panels. Use the button below to see our options

Capping Rails

Post Caps add the finishing touch to any fence, view the full range by clicking the button below

Post Caps

View our other types of fencing using the buttons below

Horizontal Hit & Miss Fence Panels

Our Hit & Miss Range

All Fence Panels

Document Downloads

• Panel fence instructions
• How to reduce the width of Jacksons Fencing Panels
• Hit Miss Vertical Panel Spec Sheet
• Q40 Hit Miss Panel Vertical
• Hit and Miss Fence Vertical 910mm - J701042sht1
• Hit and Miss Fence Vertical 1830mm - J701042sht4
• Hit and Miss Panel Vertical 1220mm - J701042sht2
• Hit and Miss Panel Vertical 1520mm - J701042sht3
• Vertical Hit n Miss Double Gate - SHORT - J702128sht4
• Vertical Hit n Miss Double Gate - TALL - J702128sht2
• Vertical Hit n Miss Single Gate - SHORT - J702128sht3
• Vertical Hit n Miss Single Gate - TALL - J702128sht1